San Antonio, Texas 78238
Follow us on

Engravable Materials

What Material Are You Looking to Engrave?

Acrylic
Acrylic
Awards & Trophies
Awards & Trophies
Fabric & Textiles
Fabric & Textiles
Glass
Glass
Firearms & NFA
Firearms & NFA
Wood
Wood

Engravable materials: what fiber and CO2 lasers can do

Choosing a laser starts with the material you need to mark, engrave, or cut. SA Laser Edge fiber lasers mark and engrave metals and some plastics. Razor CO2 machines and the Edge XC2, a 50W galvo CO2, are built for organic and non-metal work such as wood, acrylic, leather, fabric, paper, and rubber. A fiber laser does not engrave wood, glass, fabric, leather, paper, acrylic, or MDF. A CO2 laser can mark some metals with a marking compound, but it is not a substitute for a fiber laser on bare metal. Use the chart below to match the material to the machine.

Materials chart

As a galvo CO2, the Edge XC2 cuts thin materials. For thicker sheet cutting, use the Razor.

MaterialFiber (Edge)CO2 (Razor CO2 / Edge XC2, 50W galvo CO2)Notes
Stainless steelMark / Engrave / AnnealMark with compound onlyAnnealing leaves a dark mark without removing material. On CO2, bare metal needs a marking compound; CO2 is not a substitute for fiber.
Aluminum (raw)Mark / EngraveMark with compound onlyCO2 follows the bare-metal compound rule.
Aluminum (anodized)Mark / EngraveEngrave (removes the anodized layer, leaving a white or bare mark; doesn't cut the metal)CO2 removes the anodized layer and leaves a white or bare mark. It doesn't cut the metal.
SteelMark / EngraveMark with compound onlyCO2 follows the bare-metal compound rule.
TitaniumMark / EngraveMark with compound onlyOn CO2, bare metal needs a marking compound, the same bare-metal rule as steel.
BrassMark / EngraveMark with compound onlyOn CO2, bare metal needs a marking compound, the same bare-metal rule as steel.
CopperMark / Engrave (highly reflective; runs slower than steel)Mark with compound onlyCopper is highly reflective, so it runs slower than steel. On CO2, bare metal needs a marking compound.
Coated or Cerakoted metalMark / Engrave (removes the coating to bright bare metal)Engrave (removes coating); fiber gives the sharper resultFiber removes the coating to bright bare metal. CO2 engraves by removing the coating; fiber gives the sharper result.
ABS and other plasticsMark / EngraveEngrave / Cut (many plastics, including ABS); never PVC or any vinyl that contains chlorineABS and nylon or glass-filled polymers mark well on fiber. Never process PVC or any vinyl that contains chlorine.
Nylon and glass-filled polymersMark / EngraveEngrave—
WoodNoEngrave / CutAs a galvo CO2, the XC2 cuts thin materials. For thicker sheet cutting, use the Razor.
MDFNoEngrave / Cut—
AcrylicNoEngrave / Cut—
GlassNoEngrave (frosted etch), no cuttingCO2 engraves a frosted etch and does not cut glass.
LeatherNoEngrave / Cut—
FabricNoEngrave / Cut—
PaperNoEngrave / Cut—
Stone or slateLimited. Marks some dark stone and granite; CO2 is the usual choiceEngrave (frosted mark)This applies to both the Razor and the Edge XC2.
CeramicLimited, with marking compoundEngrave glazed tile, best with marking compoundA ceramic-based coating (Cerakote) is not the same as engraving ceramic ware.
RubberNoEngrave / Cut, only if it contains no chlorineRubber only if it does not contain chlorine.
PVCNo — do not processNo — do not processCutting or engraving PVC releases chlorine gas. Never process materials that contain chlorine.

Never process PVC. Cutting or engraving PVC releases chlorine gas. Do not process any material that contains chlorine, on fiber or on CO2. Use rubber only if it does not contain chlorine.

Next step. If you are matching a machine to the work you want to run, start with Fiber vs CO2 laser, then look at Edge fiber systems or CO2 systems.

If you need a part marked or engraved and you do not have a machine, see engraving services or contact SA Laser at (888) 964-3568 or customerservice@salasers.com.